- Manuals
- Brands
- Eaton Manuals
- Indoor Furnishing
- Wright-Line TechBench
- Installation manual
Hide thumbs
-
- Bookmarks
Advertisem*nt
Quick Links
Download this manual
TechBench™ Installation Manual
Table of Contents
TechBench™ Overview ...................................................................................................................2
Bench Assembly – Linear,36" (914,4mm) Wide – 96" (2438,4mm) Wide.....................3,4,5,6,7
Wide
Bench Assembly – Linear,24" (609,6mm)
– 30" (762mm) Wide................................8,9
Bench Assembly – Corner 48" (1219,2mm) x 48" (1219,2mm).............................10, 11, 12, 14
91398 Rev._B_ 11/30/16
Page 1
Advertisem*nt
Related Manuals for Eaton Wright-Line TechBench
-
Indoor Furnishing Eaton Wright-Line TechOrganizer Corner Manual
(4 pages)
-
Indoor Furnishing Eaton Profile Installation Manual
Command console (70 pages)
-
Indoor Furnishing Eaton OnGuard Installation Manual
Command console (24 pages)
-
Indoor Furnishing Eaton Linear TechBench partial shelf Installation Sheet
(2 pages)
-
Indoor Furnishing Eaton Optimedia Periodical Shelf Instruction Sheet
(3 pages)
-
Indoor Furnishing Eaton Wright-Line ALLEPSD2430 Installation Instructions
Service pullout (3 pages)
-
Indoor Furnishing Eaton ALSLCG1624 Installation Sheet
Lab sliding door compartment (6 pages)
-
Indoor Furnishing Eaton LMS Installation Manual
Technical environment systems (202 pages)
-
Indoor Furnishing Eaton Linear Tech Bench 1 Installation Manual
Sit-to-stand techbench (21 pages)
-
Indoor Furnishing Eaton Compass Installation Manual
Modular office furniture system (62 pages)
-
Indoor Furnishing Eaton Compass sit-to-stand Installation Manual
Free standing corner type and linear type.powered adjustable heightmodular office furniture system (20 pages)
-
Indoor Furnishing Eaton LINX Linear Worksurface Manual
(8 pages)
-
Indoor Furnishing Eaton LINX Installation Manual
Modular furniture (123 pages)
-
Indoor Furnishing Eaton TechBench Full Shelf Instruction Sheet
(2 pages)
Summary of Contents for Eaton Wright-Line TechBench
- Page 1 TechBench™ Installation Manual Table of Contents TechBench™ Overview ………………………………………………………………………………………………..…..2 Bench Assembly – Linear,36” (914,4mm) Wide – 96” (2438,4mm) Wide…………………3,4,5,6,7 Wide Bench Assembly – Linear,24” (609,6mm) – 30” (762mm) Wide………………….……….8,9 Bench Assembly – Corner 48” (1219,2mm) x 48” (1219,2mm)………………………..10, 11, 12, 14 91398 Rev._B_ 11/30/16 Page 1...
- Page 2 ™ TechBench Installation TechBench Overview • TechBenches are available with a 1.75" (44,5mm) thick Maple work surface, a 1.20" (30,5mm) thick Laminate work surface and a 0.75" (19,1mm) thick Phenolic work surface. • The TechBench height can be set at 1.00" (25,4mm) increments. •...
-
Page 3: Tools Required
™ TechBench ench™ Installation TOOLS REQUIRED (1) 3/8" Socket wrench (not supplied) (1) 3/8" Socket (not supplied) (1) 9/16" Socket (not supplied) (1) #1 and #2 Magnetic tip phillips head bit (not supplied) (1) Electric drill (not supplied) (2) 1/2" Open end wrench (not supplied) (3) 1"... - Page 4 TechBench™ .33nch ™ Installation 3. Assemble the Stiffener to the Upper Side Frames as shown in figures 2a and 2b. Slide the "tongue" at the end of the Stiffener into the slots on the top of the Upper Side Frames. Align the holes in the tongue with the holes in the top of the frame and secure using two 1/4"-20 x 1/2"...
-
Page 5: Installation
™ TechBench™ TechBench™ TechBench Installation 4. Attach he Upper Frame assembly to the Linear Worksurface. Refer to charts on page 9 for types of hardware used for specific Worksurface types. 91398 Rev._B_ 11/30/16 Page 5... - Page 6 TechBench™ TechBench™ TechBench™ TechBench™ TechBench™ TechBench™ TechBench™ TechBench™ TechBench™ TechBench™ Installation Installation Installation Installation TechBench™ TechBench™ 91398 Rev._B_ 11/30/16 Page 6...
- Page 7 TechBench™ Installation 5. Reassemble the Lower Side Frames to the Upper Side Frames using the carriage bolts, washers and nuts previously removed in step 2. Adjust the Lower Side Frames for the desired height of the TechBench™ and re-install the hardware as shown in figure 6a.
- Page 8 TechBench™ Installation Hex nuts Carriage bolts Washers Connector FIGURE 7A Connector location when connecting two benches together and installing cable troughs. Hex nuts Connector Washers Carriage bolts FIGURE 7B Cable trough installation only (single bench) Cable trough Cable trough Connector Connector TechBench™...
- Page 9 Techbench™ Installation Carriage bolts Washers Connector nuts FIGURE 7D Connector location when connecting two benches together. 91398 Rev._B_ 11/30/16 Page 9...
- Page 10 Techbench™ Installation LINEAR BENCH ASSEMBLY (24" wide and 30" wide) 1. With two people, carefully unpack the worksurface Upper Side Frame and place it finished side down on the empty carton or on a clean carpeted surface. NOTE: Pre-drilled mounting holes in underside of worksurface are visible.
- Page 11 Techbench™ Installation 91398 Rev._B_ 11/30/16 Page 11...
- Page 12 TechBench ™ Installation 6. Reassemble the Lower Side Frames to the Upper Side Frames using the carriage bolts, washers and nuts previously removed in step 2. Adjust the Lower Side Frames for the desired height of the TechBench™ and re-install the hardware as shown in figure 11a.
- Page 13 TechBench™ Installation CORNER BENCH ASSEMBLY 1. With two people, carefully unpack the Worksurface and place it finished side down on the empty carton or on a clean carpeted surface. NOTE: Pre-drilled mounting holes in underside of worksurface are visible. Corner TechBench™ 2.
- Page 14 TechBench™ Installation 3. Assemble the Stiffeners to the Upper Side Frames and Upper Corner Post as shown in figures 13. Slide the "tongue" at the end of the Stiffeners into the slots on the top of the Upper Side Frames. See Detail A. Align the holes in the tongue with the holes in the top of the frame and secure using two 1/4"-20 x 1/2"...
- Page 15 TechBench™ Installation 4. Assemble two Gusset Adapters to the Worksurface using two #10 x 5/8" phillips head screws. See figure 14. 5. Turn the Upper Frame assembly over and position it on the worksurface as shown in figure 15. #10 x 5/8" phillips head screws Corner Worksurface Align open end of...
- Page 16 Techbench™ Installation (10) #10 x 5/8" phillips head screws 6. Attach the Upper Frame assembly to the Corner Upper Frame assembly Worksurface using the hardware provided. For Laminate Worksurfaces, refer to figure 16. For Maple Worksurfaces, refer to figure 17. For Phenolic Worksurfaces, refer to figure 18.
- Page 17 Techbench™ Installation 7. Reassemble the Lower Side Frames and Upper Corner Post using the carriage bolts, washers and nuts previously removed in step 2. Adjust the Lower Side Frames and Lower Corner Post for the desired height of the TechBench™ and re-install the hardware as shown in figure 19a.
- Page 18 Techbench™ Installation TOOLS REQUIRED (1) 3/8" Socket wrench (not supplied) (1) 3/8" Socket (not supplied) (1) 9/16" Socket (not supplied) (1) #1 and #2 Magnetic tip phillips head bit (not supplied) (1) Electric drill (not supplied) (2) 1/2" Open end wrench (not supplied) (3) 1"...
